Pro duct7 - Bulk Cloned-manufacture,factory,supplier from China

      Density board is called density fiberboard. It is made of wood fiber or other plant fiber, prepared by fiber, applied with synthetic resin, and pressed under heat and pressure.     According to its density, it can be divided into high-density fiberboard, medium-density fiberboard and low-density fiberboard.

    MDF is actually a kind of density board, which also includes short fiberboard and long fiberboard. MDF is mainly made of plant fibers or wood fibers. After the fibers are crushed, separated, and dried, a urea-formaldehyde resin or other suitable adhesive is added and pressed at high temperature. This kind of man-made board is often used in interior decoration.Xinhua Wood Storage  Quality Certificates  Gaotang County Xinhua Wood Industry Co., Ltd. was established in April 2010 with a registered capital of 11 million yuan.

Moistureproof board is to add a certain proportion of moistureproof particles in the production process of the base material, also known as melamine board (base material), which can greatly reduce the degree of expansion of the board when encountering water.  Gaotang County Xinhua Wood Industry Co., Ltd. was established in April 2010 with a registered capital of 11 million yuan. It covers an area of about 76,600 square meters, including a construction area of about 22,000 square meters.

   Density board, also known as fiberboard, is an artificial board made of wood fiber or other plant fiber by hot pressing after slicing, cooking, fiber separation, and drying, then applying urea-formaldehyde resin or other suitable adhesives. the   According to the density, it can be divided into low-density board (weight less than 550KG/M3), also known as low-density fiberboard. Medium density board (weight 550~880KG/M3), also known as medium density fiberboard.

     Particleboard, as a very common decorative material at home and abroad, in addition to conventional furniture manufacturing, particleboard actually has other wider uses, such as suspended ceilings, partition walls, interior decoration, etc.Particleboard has uniform density and thickness, and smooth surface. It is a good veneer substrate. Industrial-grade particleboard can be used in many veneer materials and is very suitable as a veneer substrate.  2.Particleboard furniture refers to furniture that directly uses particleboard as a finish.

      Waterproof and moisture-proof board is made by adding special materials that can improve the waterproof, moisture-proof and mildew-proof performance of wood-based panels during the production of medium-density fiberboard.   It is suitable for high-humidity areas and places where accidental humidity may occur, such as kitchens Cabinets, bathroom vanity, laundry cabinet. Marked in green.

  Density board is made of wood fiber or other plant fiber, prepared by fiber, applied with synthetic resin, and pressed under heat and pressure.Certificates ISO FSC SGS  

Advantages and disadvantages of MDFI. Advantages1. MDF processing is simpleMDF is very simple in the finishing process. Most paints and paints can be evenly applied on the MDF, and the effect is very good. It is the first choice for those who want to chase the paint effect.2. Beautiful appearance, easy to decorateMDF is a kind of decorative board with very exquisite appearance, and all kinds of wood veneer, adhesive tape film, veneer, light metal sheet lamp material can be pasted on MDF by glue to make its surface look more exquisite. Therefore, it is favored by everyone in home decoration.3.

    Particleboard, also known as chipboard, flakeboard, is a wood-based panel that is made of wood or other lignocellulosic materials and glued under heat and pressure after applying an adhesive. It is mainly used in furniture manufacturing and construction industry as well as train and car carriage manufacturing.Method for judging the quality of particleboard wardrobes1. From the appearance point of view, look at the size and shape of the sawdust particles in the center of the cross section. The length is generally 5-10MM.

     Density board is called medium density fiberboard（MDF) . It is made of wood fiber or other plant fiber, prepared by fiber, applied with synthetic resin, and pressed under heat and pressure. According to its density, it can be divided into high-density fiberboard, medium-density fiberboard and low-density fiberboard. It is widely used in the fields of furniture manufacturing and decoration in China.Xinhua Wood Show  Xinhua Wood Machinery  Gaotang County Xinhua Wood Industry Co., Ltd.

     Density board, also known as fiberboard, is an artificial board made of wood fiber or other plant fiber by hot pressing after slicing, cooking, fiber separation, and drying, then applying urea-formaldehyde resin or other suitable adhesives.     The biggest advantage of MDF (medium fiberboard) is that it can be used for carving, engraving and milling, so as to make various shapes.

Advantages of carbon crystal panels in customized home furnishing The carbon crystal plate is made of a PVC film on the base material. The veneer can not only play a decorative role, but also protect the inside of the plate from external erosion, replacing the position of the paint. Therefore, the carbon crystal plate is used in There is no need to paint at all times, which is very convenient and trouble-free.

Carbon Crystal Panel and Its AdvantagesCarbon crystal panel is generally used in paint-free technology, with high environmental protection and good moisture resistance. In terms of materials, they all belong to composite boards. If they are under the same brand, the quality of carbon crystal boards is better. In contrast, carbon crystal panels are waterproof, moisture-proof, environmentally friendly, formaldehyde-free, crack-resistant and non-deformable. Carbon crystal plate is a new type of high-tech environmental protection material.

Soak the common substrate and moisture-proof substrate in water at the same time, and the expansion rate of the common plate is significantly higher than that of the moisture-proof plate after two hours of expansion change. The moisture-proof board has good moisture-proof performance and is suitable for making kitchen furniture and bathroom furniture.Damp-proof board cannot be directly used on furniture, and decorative paper should be pasted on the surface. The normal practice is to soak the decorative paper in melamine solution, and then press it on after hot pressing.

The following aspects should be paid attention to when choosing medium density fiberboard;1. From the appearance, check whether the thickness and density are uniform, whether the corners are damaged, whether there are delamination, blister, charcolization, etc., and whether there are soft parts.2. When conditions permit, you can saw a small piece of medium density fiberboard and soak it in water with a water temperature of 20°C for 24 hours to observe its thickness change, and at the same time observe whether there are small bulges on the surface of the board.

   MDF is a man-made board made of wood or plant fiber, mixed with adhesives and waterproofing agents, etc., and pressed under high temperature and high pressure. It is an ideal man-made board for furniture production.Advantages of MDF:Medium density fiberboard has uniform internal structure, moderate density, strong stability, not easy to deform or crack, and durable.2. Medium density fiberboard has a smooth surface, strong plasticity, and good production and processing performance.

    For furniture manufacturing, the most common and most widely used in the market is mainly MDF, with a density of 680~830KG/M3. It is widely used in the manufacture of cabinets, beds, wooden doors, tables and chairs, showcases and other furniture, as well as wooden items such as gift boxes, photo frames, stereos, props, etc. It is also a common board for interior decoration, basically most of the furniture around you Products have the material composition of density board.The surface of products with a thickness of 6mm or less can also be divided into matte and sanding effects.

The reason for the deformation of density board furniture is here?    We all know that MDF has a wide range of applications. However, furniture made of this kind of board often has such a problem: the furniture board is deformed, which is very annoying.It not only seriously affects the normal use of our furniture, but also has a bad influence on family life. We knowThere are many reasons for this problem, and we will introduce them in detail below.1.

Is MDF or solid wood particle board better? Compare the advantages and disadvantages of the two:MDF:Advantages: The material is delicate, the edge sealing of the cutting surface is well done, it is not easy to open the glue, and it is convenient to make various shapes, so it is often used to make door panels or back panels.2. Disadvantages: The base material is powder, and the glue used is more than particle board, so it is easy to have environmental protection problems.

A. What material is MDF made of?1. Medium fiberboard is a kind of density board, which is divided into long fiberboard and short fiberboard. Its raw materials are mainly wood fibers or other plant fibers, which are made after crushing, fiber separation, drying, applying urea-formaldehyde resin or other suitable adhesives, and then hot pressing.2. MDF has a square and smooth surface, and its processing performance is excellent. It can be pasted with sliced veneer. It is often used to make furniture, partitions, etc.

How is Xinhua Wood MDF Board?    Xinhua Wood MDF board use fresh polar pine willlow or combi hardwood as raw material, advanced equipments mature production technology, strict quality control systerm , always a pre-production sample and check quality before packing, which ensure good quality and Xinhua Wood has 4 production lines , monthly output 50000 cbm, with sufficient stocks ,can deliver in 15-25 days.MDF Product DisplayThe Usage of MDF Fiberboard Furniture manufacturing: At present, MDF is mainly used to replace natural wood for furniture production.

    MDF is actually a kind of density board, which also includes short fiberboard and long fiberboard. MDF is mainly made of plant fibers or wood fibers. After the fibers are crushed, separated, and dried, a urea-formaldehyde resin or other suitable adhesive is added and pressed at high temperature. A kind of man-made board.The thickness of MDF is generally between 3mm-30mm, and the density of MDF is very high. Generally, the choice of MDF depends on the density of MDF to determine the quality of MDF. The density of MDF is generally It is in the range of 0.5-0.8g/cm³.

Everyone knows that density board is widely used in making furniture or decorating partitions because of its uniform structure, fine material, stable performance and easy processing. Everyone is curious, how to distinguish the quality of density board?Let me tell you something.1. Surface cleanliness: There should be no obvious particles on the surface of the density board with good surface cleanliness. Particles are caused by impurities brought in during the pressing process, which not only affects the appearance, but also makes the paint film easy to peel off.2.

What are the advantages of decorative board MDF?    Density board, also known as fiberboard, is a man-made board made of wood fiber or other plant fiber and applied with urea-formaldehyde resin or other suitable adhesives. According to its density, it can be divided into high density board, medium density board and low density board. Due to its softness, impact resistance and easy reprocessing, MDF is a good material for making furniture abroad. Density board is easy to finishing.